redordead's 1989 Honda CR 250
Info: VERY HANDY HAVING A SPARE 89 FRAME TO SAVE MIXING MY BOLTS UP WHILE THE FRAME 'S BEING STRIPPED!
Views / Day: 0.1
640x480 / 72 KB

 
Info: NITROMORSE:-)))))))))
Views / Day: 0.2
480x640 / 67 KB

 
Info: DAMMIT I SHOULD HAVE BOUGHT THE BIG BOTTLE! AH WELL BACK TO THE SHOP IN THE MORNING:-)
Views / Day: 0.2
640x480 / 81 KB

 
Info: MY WIFE MAY YET BAN THE POSTMAN FROM MY HOUSE :-))))))))))
BUT NEW BITS ARE MORE THAN WELCOME!
Views / Day: 0.2
640x480 / 56 KB

 
Info: MERRY XMAS TO ME ;-)
NEW SEAT COVER FOR MY REBUILD JUST ARRIVED!
NEW ALL BALLS LINKAGE KIT ON ITS WAY SO I WILL DO A STEP BY STEP LINKAGE REBUILD AND SEAT RE-COVERING AND UPLOAD THE PHOTOS SOON!
Views / Day: 0.2
640x480 / 63 KB

 
Info: :-)))) MY NEW 89 CR250R ALL BALLS LINKAGE KIT JUST ARRIVED,:-))))
Views / Day: 0.1
640x480 / 42 KB

 
Info: Near perfect 1991 cr250 forks to be used as donors for upper tubes as they're a far nicer shade of gold!
Both lower stanchons, single sided clamp and threaded spindle, all internals and top air valve...
Views / Day: 0.1
640x480 / 51 KB

 
Info: My new donor KZ4 831 1991 cr250 upper tubes being swapped for my shabby worn 89 cr250 upper tubes!
Views / Day: 0.2
640x480 / 42 KB

 
Info: My new donor forks!
Views / Day: 0.2
640x480 / 65 KB

 
Info: Took a bit of elbow grease but its nice n clean for the rebuild
Views / Day: 0.2
640x480 / 59 KB

 
Info: Flipside! as i said nice and clean!
Views / Day: 0.1
640x480 / 79 KB

 
Info: Now replaced by a nice nos item!

Front calliper carrier after a bit of a workout:-)
Views / Day: 0.2
640x480 / 67 KB

 
Info: FINALLY GOT A BIT OF TIME TO DO MY
89 CR250 LINKAGE STRIP AND ALL BALLS REBUILD!
Views / Day: 0.1
640x480 / 55 KB

 
Info: 
This linkage knuckle has now been replaced along with the whole swing arm  due to a hairline crack along the factory weld on the drive side of the upper swing arm hump
FIRST UP THE LOWER SHOCK BEAR...
Views / Day: 0.1
640x480 / 59 KB

 
Info: 89 CR250 LINKAGE SEAL REMOVAL! 
BE CAREFUL NOT TO SCORE THE INNER SURFACES!
Views / Day: 0.1
640x480 / 72 KB

 
Info: 1989 CR250 LINKAGE REBUILD,
WELL RUSTY DRY BEARINGS ARE NOT THE EASIEST TO WORK WITH SO IT PAYS TO DO THIS EVERY COUPLE OF YEARS!
ACCESS TO A BLOW TORCH OR GAMPING GAZ BLOW TORCH ESSENTIAL FOR BEARI...
Views / Day: 0.1
640x480 / 83 KB

 
Info: MAKE SURE ALL SURFACES ARE CLEANED AND  FREE FROM SCRAPES AFTER YOU REMOVE THE OLD SEALS AND BEARINGS.
Views / Day: 0.1
640x480 / 87 KB

 
Info: 1989 CR250 LINKAGE REBUILD
BOTH OF THE COLLAR BUSHES FROM THESE BEARINGS CAME OUT NO PROBS AND OFFERD VERY LITTLE RESISTANCY!
ONE LAST COLLAR BUSH AND THEN BEARING REMOVAL!
Views / Day: 0.1
640x480 / 85 KB

 
Info: 1989 CR250 LINKAGE REBUILD
ALL BEARINGS SEALS AND BUSHES NOW GONE AFTER A LENGTHY EVENING IN THE WORKSHOP.:-)))))
QUITE A COMMON PROBLEM WITH THESE LINKAGES IS WEAR ON THE INSIDE OF THE FORK PART OF...
Views / Day: 0.2
640x480 / 56 KB

 
Info: 1989 HONDA CR250 LINKAGE STRIP AND REBUILD
I WILL DO STEP BY STEP PHOTO SHOTS OF THE NEW ALL BALLS KIT GOING IN TOMORROW NIGHT AND UPLOAD THEM LATER THIS WEEK!
Views / Day: 0.2
640x480 / 61 KB

 
Info: BRAND NEW RENTHALS FITTED A WEEK BEFORE I STRIPPED IT AND AS YET REMAIN UNUSED:-(
Views / Day: 0.1
640x480 / 87 KB

 
Info: Another part among several hundred replaced on my bike!
On a very sad note the near mint replacement kicker among a couple of other parts came from David livesey who recently passed away.
Views / Day: 0.1
640x480 / 44 KB

 
Info: HONDA MINI MADNESS
1 X 1984 HONDA CR50 RE ( FRONT CENTER VERY RARE )
4.5 X 82 - 85 HONDA ATC70'S
1 X 03ISH HONDA XR100R ( FAR LEFT )WHICH WAS SOON TO BE A DONOR FOR A ONE OFF MAD ASS TRIKE!
IF YOU...
Views / Day: 0.2
640x480 / 75 KB

 
Info: HEY PRESTO HERES THE RESULT!
ATC110 FRONT END,
ATC70 CHASSIS PLASTICS WITH NBC SMOCK SEAT COVER AND 70 REAR AXLE,
XR100R ENGINE AND TANK:-)))))))
Views / Day: 0.2
2048x1536 / 677 KB

 
< BACK
Page: [1] <2> [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14]
Sort By: Date / Img Width / File Size
NEXT >
Photos: 335
Purchased: Jun 2011
Sold: n/a
Information: My 2 year project to make a practically brand new bike from an old rider! Over 6000 now spent creating this and now in the final stretch I can''t wait to finish her off :-))))) DONE DUSTED AND NOW SOLD!!!! All the very best to her new owner who might be racing her this season in the Dave Thorpe evo series in England;-))))

Related Links:
Return to redordead's BikePics Member Page
Return to the BikePics 1989 Honda CR 250 Page
Return to the BikePics Honda CR 250 Page
Return to the BikePics Honda Page



1997-2014 Bikepics PTY LTD