redordead's 1989 Honda CR 250
Info: 89 CR250 Airbox to carb boot stay plate after an hours careful cleaning! I have a mint airbox and cage/boot etc to make a mint full assembly including ridiculously rare NOS airbox lid and caution deca...
Views / Day: 0.2
640x480 / 60 KB

 
Info: Near mint 89 CR250 rear shock from an ultra low hour bike in California:-) It needs a new bottom rubber bump stop due to the old one being like a crumbly cake because of the good old Cali sun and heat...
Views / Day: 0.2
640x480 / 65 KB

 
Info: Near mint 89 cr250 rear shock with the original label showing almost no wear at all!
It has just had a new top bearing fitted so my brand new replacement all balls unit will be passed on to the next ...
Views / Day: 0.2
640x480 / 60 KB

 
Info: 1989 CR250RK top yoke / fork clamp nearing being good enough for a final polish and seal after around 2 dozen hours hand prepping with all grades of sanding sponges and wet and dry to remove cast line...
Views / Day: 0.3
640x480 / 72 KB

 
Info: More polishing on my 1989 cr250 upper yoke / clamp
Views / Day: 0.2
640x480 / 68 KB

 
Info: Wheres Wally? 
Spot the top yoke!
After many hours of careful prep you can easily achieve a nice finish to call your own so don't be afraid to get stuck in but just choose your tools wisely and don'...
Views / Day: 0.3
640x480 / 76 KB

 
Info: The latest arrival from USA! This is set #2 as the swingarm has 4 of these bearings! 
I have almost all parts to service my swingarm back to as new spec so when i build it i will do a shot by shot se...
Views / Day: 0.2
640x480 / 65 KB

 
Info: The latest group photo of nearly all the Nos and new parts i have to rebuild my 89 cr250 :-)))))
Views / Day: 0.3
640x480 / 81 KB

 
Info: from another angle!
Views / Day: 0.3
640x480 / 71 KB

 
Info: pic 3
Views / Day: 0.2
640x480 / 54 KB

 
Info: I couldn't fit it all on the leather so heres more on the floor!
Views / Day: 0.2
640x480 / 57 KB

 
Info: A lot of new parts have already been fitted to some assemblies like the new rear Excel pro rim on new spokes and bearings etc,
The engine has already been rebuilt with full NOS honda gasket kit and N...
Views / Day: 0.2
640x480 / 55 KB

 
Info: I spent a bit of time on the swingarm this week and got a good mirror finish after several grades of polishing and some mightily sore forearms! 
Worth it so just about ready for nos rebuild (see next...
Views / Day: 0.2
640x480 / 67 KB

 
Info: Most of the assembled nos parts for my 89 cr250 swingarm!
Chain slide is on its way from the states:-)
Views / Day: 0.2
640x480 / 76 KB

 
Info: Mirror polished 1989 cr250 swingarm
A good finish is only a sore arm away so soak up the pain and make it your own!
The stonking RC30 in the photo was completely built from spares and is featured in...
Views / Day: 0.2
640x480 / 66 KB

 
Info: JUST FITTED UP THE NEW RAD SCOOPS ON THE REPLACEMENT TANK FOR THE FIRST TIME SINCE I GOT THE TANK FROM FLORIDA AGES AGO!
Views / Day: 0.2
640x480 / 49 KB

 
Info: THANKFULLY THE NEW UFO SCOOPS ARE A GOOD COLOUR MATCH ON THE FIGHTING RED TANK :-)
Views / Day: 0.2
480x640 / 55 KB

 
Info: A LITTLE TIME AND EFFORT REQUIRED TO BRING UP THE TANK AND IT'LL BE READY TO GO ON THE FRAME!
Views / Day: 0.2
480x640 / 46 KB

 
Info: One of the few remaining items to be checked off my verrrrry long replacement list:-) Just arrived from the states and for once i didn't get bent over for customs;-)
Views / Day: 0.2
640x480 / 61 KB

 
Info: Nearly all the new parts for the swingarm!
I'm a bit reluctant to fit the new bearings and seals to the swingarm as the ones that came in it from Cali are practically brand new as are the linkage bea...
Views / Day: 0.1
640x480 / 81 KB

 
Info: Most of the parts for rebuilding my airbox!
It should be quite a nice assembly when together so watch this space!
Views / Day: 0.2
640x480 / 72 KB

 
Info: The bouncy bits;-)
Views / Day: 0.2
640x480 / 56 KB

 
Info: New throttle tube courtesy of Devines Honda in Glasgow, Came via Belgium cost just over a tenner and got here in only two days!
Views / Day: 0.1
640x480 / 44 KB

 
Info: My frame, decals and plastics, Still undecided on which rad scoop decals to use:-(
Views / Day: 0.2
640x480 / 60 KB

 
< BACK
Page: [1] [2] [3] [4] [5] [6] [7] [8] <9> [10] [11] [12] [13] [14]
Sort By: Date / Img Width / File Size
NEXT >
Photos: 335
Purchased: Jun 2011
Sold: n/a
Information: My 2 year project to make a practically brand new bike from an old rider! Over 6000 now spent creating this and now in the final stretch I can''t wait to finish her off :-))))) DONE DUSTED AND NOW SOLD!!!! All the very best to her new owner who might be racing her this season in the Dave Thorpe evo series in England;-))))

Related Links:
Return to redordead's BikePics Member Page
Return to the BikePics 1989 Honda CR 250 Page
Return to the BikePics Honda CR 250 Page
Return to the BikePics Honda Page



1997-2014 Bikepics PTY LTD